Reverse Osmosis Scale Inhibitor RENATUR 332 for RO Systems


Release time:

2026-11-18

Renature supplies the reverse osmosis scale inhibitor RENATUR 332 for RO systems that face carbonate and sulfate scaling. The product is described as a biomass based hyper-branched polymer that is free of nitrogen and phosphorus and is biochemically degradable. It is intended for surface water, groundwater and brackish water before the membrane.

What the Inhibitor Controls

RENATUR 332 is formulated to prevent the fouling of inorganic salt scales from carbonate, sulfate and phosphate. The page states that it can meet more than 98 percent of conventional water quality standards and that it is effective against carbonate, sulfate and phosphate scaling across the recommended range.

The product also targets non-polymeric iron and aluminum pollution, with a limit value of 0.6 ppm on the concentrated water side. It has a scale-inhibiting and dispersing effect on silica, with no scaling risk listed when the silicon dioxide content on the concentrate side is within 100 ppm. That combination is useful where a plant sees several foulants rather than a single salt.

The page states that the inhibitor can prevent reverse osmosis organic pollution to a certain extent and can adapt to a slightly higher COD before the membrane. That does not replace a proper pretreatment review, but it gives the operator more margin when the feed quality changes.

Operating Range and Dose

The applicable pH range is 6 to 11 and the applicable temperature range is 0 to 45 degrees Celsius. The product is a concentrated liquid with an active ingredient content of at least 42 percent. The appearance is a light yellow to amber transparent liquid, the density at 25 degrees Celsius is 1.15 to 1.25 grams per cubic centimeter, and the pH of the original fluid is 1.0 to 3.0.

The usual dose is 0.2 to 0.5 ppm. The exact dose should be set from the water analysis and the recovery of the RO system, not from the general range alone. A plant with high hardness, high silica or a high concentration factor may need a different dose from a plant with low salinity feed.

The chelation and dispersion value is listed as 410 to 420 milligrams of calcium carbonate per gram of dry basis inhibitor. That figure is a useful comparison point when a buyer evaluates another product, but the test method should be the same before the numbers are compared.

Because the product is a concentrated liquid, the dosing system should be checked for compatibility with the low pH of the original fluid. The dilution water, the pump materials and the injection point should be confirmed with the supplier before the product is put into service.

Water Quality and System Checks

Before selecting the reverse osmosis scale inhibitor, review the feed water analysis, the pretreatment train, the membrane type and the recovery. The inhibitor is designed for conventional water quality, so an unusual feed may need a different product or a different pretreatment step.

Monitor the normalized permeate flow, the pressure drop and the salt passage after the product is introduced. A stable normalized flow and a stable pressure drop are the practical signs that the scaling control is working. If the pressure drop rises, check the dose, the injection point and the pretreatment before changing the product.

The page states that the product is suitable for food processing, beverage production, energy and power industries. A food or beverage plant should also confirm the food contact and discharge requirements for the product in the destination country, because those rules vary by market.

Supply and Ordering

Renature focuses on water treatment and desalination, with membrane system engineering, chemical supply, third-party operation and maintenance, and tools and equipment. A plant can ask for the product alone or for support with the dosing and monitoring plan.

To request a quotation, send the feed water analysis, the RO system capacity, the recovery, the current dose and the destination. Our team will confirm the RENATUR 332 specification and the packing size. A trial order should include a dosing plan and a monitoring sheet.

For technical questions, contact sales@renatur.cn. Our team can review the scaling risk and the recommended reverse osmosis scale inhibitor dose for the system.

If you are comparing inhibitors, ask for the active content, the density, the pH and the chelation value on the same basis. A low price per kilogram can hide a higher dose, and the cost per cubic meter of permeate is the number that matters.

©2025 Renatur Environmental Protection Technology (Dalian) Co., Ltd. Powered by:CEglobal

Business License